Material Testing Lab Instruments

This is Portable Type Universal Testing Machine which will give YS, UTS, Fractured Toughness, Brinell Hardness, Vickers Hardness.

Mubatec HU-1+ labor frame
With labor frame allows to make tests of samples and samll-sized details and calibrate Portable Instrument Indentation HU1-1

Mubatec HU-1+ magnetic frame
With magnetic shoes allow to control vessels and pipelines almost all sizes made from magnetic materials

Mubatec HU-1+ strap chain frame
With straps frame allow to control small and middle-sized vessels and pipelines from non-magnetic materials

Mubatec HU-m+robotized frame
With robotized frame with automatic polishing of controlled place allows to make control in adverse enviroment including vessels of nuclear reactors

Brief Introduction:
TECH-600C computer controlled servo hydraulic universal testing machine is mainly used to execute the tension, compression, bending, flexural etc. Test for metal materials. Attached with simple accessories and devices, it can be used to test wood, concrete, cement, rubber, and so on. It is very suitable for making test to different metal or nonmetal materials under high toughness and hardness against extreme big loading force.

Technosys offer Vickers Hardness Tester, which is used in carrying out tests related to scratch resistance under specified loads. With involved tests conducted on go/no go basis, the testing is performed at single specified load on needle as well as on the basis of process comprising increasing loads for determining minimum load at which coating penetration is achieved.

Specifications:

Technosys Systems Hardness Testers Models TECH RAS, TECH RASM, TECH RAB-1, TECH RAB-250, TECH TWIN are manually operated. All these models are suitable for testing hardness of metals & alloys of all kinds hard or soft, whether flat, round or irregular in shape. These testers are simple in design & easy to operate, yet sensitive & accurate. Various models from the wide range are suitable for Engg. Colleges, laboratories, toolroom, inspection departments, factories etc.

Specification:

Rockwell & Rockwell superficial tests consists of forcing an indentor (Diamond or Ball) into the surface of a test piece in two steps i.e. first with preliminary test force and thereafter with additional test force & the measuring depth of indentation after removal of additional test force (Remaining preliminary test force active) for measurement or hardness value. OPERATION : For Rockwell & Rockwell Superficial

 

OPERATION :For Rockwell & Rockwell Superficial Test :

In case of 'RASN' series machines for Rockwell or Rockwell Superficial Test a preliminary test force in first applied & then indicator is automatically set for zero. Quickly thereafter & additional test force is applied without removing the preliminary test force. When the penetration is stabilized, the additional test force is removed & the hardness number is shown directly on the indicator.The operation is exactly same as above. However, the diameter of impression is measured out side of machine by rockwell microscope. rockwell Hardness number is found out by referring corresponding hardness tables showing hardness number against di. of indentation for specified ball diameter and test force.

The Pendulum is mounted on antifriction bearings. It has two starting positions, the upper one for Charpy & the lower one for izod testing. On release, the pendulum swings down to brake the specimen and the energy absorbed in doing so is measured as the difference between the height of drop before rupture and the height of rise after rupture of the test specimen and is read from the maximum pointer position on the dial scale. (It is read on Digital Panel in case of digital models)Controls Pendulum:The Pendulum supports in the starting positions is by a self resetting latch. The release mechanism is operated by lever. The pendulum release latch is operated only when this lever is operatedStrikers & Supports There are two strikers and one combined support available for lifting in to the pendulum and on to the base of the machine for Izod., Charpy test, Changing from one striker to another is achieved simply by fixing the new striker into it's position.

 Charpy Test:

The Charpy test piece rests on alloy support anvils, fitted on the base of the machine rigidly held in position by Allen screws. End stopper is provided for quickly and accurately locating the test piece centrally between the supports.

 

Izod Test:

The Izod test is clamped vertically in Izod support fitted on the base of the machine. The support is provided with a machined vertical groove to suit the test piece size. The front clamp piece and the Allen screw enable clamping of the test piece in correct height with the help of Izod setting gauge supplied.

 

• Caliper gauge for checking V notch for Izod & Charpy.
• Templates for checking 10 x 10 mm cross section of Izod / Charpy test specimen
• Depth notch gauge including V & U notch gauges for checking depth blow V/U notch, angle and radius.
• Self centering tong for quick and accurate setting of Charpy test specimen.

This machine is used to test the fatigue strength of materials and to draw S-N diagram by research institute, laboratories, material manufacturers and various industries. This is rotating beam type machine in which load is applied in reversed bending fashion. The standard 8 mm dia specimen is held in special holders at its ends and located such that it experiences a uniform bending moment. The specimen is rotated at 4200 rpm by a motor. A complete cycle of reversed stresses in all fibres of the specimen is produced during each revolution.The bending moment is applied with the lever system and can be easily changed by moving a weight over the lever. Total number of revolution at which the specimen fails are recorded by a mechanical counter. An interlocking system puts off the motor at specimen failure. Machine meets requirement of IS 5075-1969.

• 6 digit electronic counter instead of mechanical counter can be supplied at additional price.
• Machine with maximum bending moment upto 400 Kg. cm can be offered on request.

Specification:

 

Features:

• Table model, no need of foundation.
• Simple lever system for changing load.
• Calibration in Nm available on request.
• Light weight, Simple design, Compact Size.

Metals play an important role in almost all industries. Uncovering the strength of metals, its microstructure, plays vital role in their application and uses. There are some crucial uses of metals, where, even tiniest impurity can create havoc in their application.Technosys Systems manufacture a whole lot of products for metal testing. From Destructive to Non Destructive Testing and from manual to servo based machines, we have machines to test each and every aspect of Metals and Metallurgical products.

Metal Testing Testing Product:

• Hydraulic UTM(Closed Head Design) Mechanical Dial Type
• Hydraulic UTM (Closed Head Design) Electronic Microprocessor Based
• Hydraulic Computerized (Close Head Design)
• Hydraulic Servo Control (Closed Head Design)
• Accessories for UTM
• EDW (Ball Screw Driven Electro-Mechanical Series)
• Tensile Testing Machine
• Test Accessories for Computer Controlled Electro-Mechanical Testing Machine
• Micro Computer Controlled Torsion Testing Machine (TW Series)
• Impact Tester
• Charpy Impact Tester Machine (Micro Computer Controlled)
• Projection Screen & Low Temperature Chamber
• Rockwell Hardness Tester
• Automatic Rockwell Hardness Tester
• Brinell Hardness Tester (Hydraulic Mechanical Type)
• Brinell Hardness Tester (Electronic Micro-Processor Based)
• Fatigue Testing Machine
• Portable Hardness Tester

Technosys Offer Brinell Hardness Tester of metals and alloys. The load is applied by manually and the indentation is read with the help of a Brinell Microscope. We well renowned portable hardness tester manufacturer. Team of experts and cutting edge technology are our strengths through which it is possible to get a excellent hardness testers that are wonderfully serving various sectors. Known for quality and we never compromise on that.

Technosys one of the prominent manufacturer and supplier of quality wide range of Vickers Cum Brinell Hardness Tester, we are engaged in providing quality products to our valuable clients as per industry standard, our products are best in industry and know for their premium quality and high performance. These testers can be availed at availed at market leading prices.

Specifications:

• Dimensions (L X W X H mm) Approx.: 650 X 320 X 990

FEATURES:

• Suitable for Torsion and Twist test on various metal rods and flats.
• Torque Measurement by pendulum dynamometer system.
• Auto torque selector to adjust torque ranges.
• Geared motor to apply torque to specimen through gearbox.
• Autographic recorder for relation between torque and angle of twist.

 

Technical Specification

Backed by a team of dedicated and skilled professionals, we are able to offer a large variety of Spring Testing Machine. These are used under the compression and tension loads. Its induction motor rotates the specimen and cut off switch stops the functioning of machine at the time of failure.

LEAF SPRING TESTING MACHINES:

We are manufacturing and supplying a wide range of Heat Transfer instruments for numerous Private units, Research Institutions, Engineering colleges, Technical institutes, R & D labs, WALMI, ICAR and other Govt. Organizations

Product Specification Heat Transfer Lab.

Features:

• Working Distance 60mm. (approx).
• Image Erect Image.
• Observation Tube Monocular Inclined At 30˚.
• Stand Large And Heavy Base Provide Extra Overall Rigidity To The Instrument.
• Eye Piece Protector Graduated 0˚ To 360˚ With Adjustable Vernier Of Least Count 6 Minutes.
• Illumination Built In Base Transmitted From 6v – 20w
• Halogen Lamp Or Led 3w-3vand Incident From Two Lamps With Variable Separate Control On Front Panel.