Technosys Systems

Make : TECHNOSYS
1. BASE MODULE FOR EXPERIMENTS WITH ACCESSORIES
Model No : FM-215 A  
2. EXPERIMENTAL SETUP FOR ANALYZING MINOR LOSSES IN PIPING SYSTEM
Model No : FM-215 B 
3. EXPERIMENTAL SETUP FOR ESTIMATING PIPE FRICTION IN LAMINAR/TURBULANT FLOW
Model No : FM-215 C 
4. EXPERIMENTAL SETUP FOR UNDERSTANDING THE MECHANISMS OF FREE & FORCED VORTEX FORMATION
Model No : FM-215 D 
5. EXPERIMENTAL SETUP FOR ESTIMATING PRESSURE DISTRIBUTION IN LIQUIDS
Model No : FM-215 E 
Technical data Pump • power consumption: 250W • max. flow rate: 150L/min • max. head: 7,6m Storage tank, capacity: 180L Measuring tank • at large volumetric flow rates: 60L • at small volumetric flow rates: 10L Flume ▪ • LxWxH: 530x150x180mm Measuring beaker with scale for very small volumetric flow rates • capacity: 2L Stopwatch ▪ • measuring range: 0…9h 59min 59sec 230V, 50Hz, 1 phase 230V, 60Hz, 1 phase; 120V, 60Hz, 1 phase 


Technical data Pipe, PVC • inner diameter: 17mm Pipe elements, PVC Inner diameter: d • contraction: from d=17 to d=9,2mm • enlargement: from d=9,2 to d=17mm • segment bend: d=17mm, 90° • pipe angle: d=19mm, 90° • narrow pipe bend: d=18mm, r=40mm, 90° • wide pipe bend: d=17mm, r=100mm, 90° Measuring ranges • pressure: o 1x 0…0,6bar o 6x 0…290mmWC

 Technical Details 2 pipe sections • length: 400mm • Ø inner: o 1x 3-4mm o 1x 8-10mm Tank: approx. 2L Measuring ranges • differential pressure: o 2x 370mmWC o 1x 0…0,25bar

The setup is designed to study the performance of reciprocating pump. Set up consists of a reciprocating pump coupled with electrical motor, supply tank, measuring tank & pipe fittings for closed loop water circulation. Pressure and Vacuum gauges are connected on delivery and suction side of pump for the purpose of measurement. The flow rate of water is measured using measuring tank and stop watch provided.

EXPERIMENTATIONS:
1.To determine the overall efficiency of reciprocating pump
2.To Plot Head Vs. Discharge, Pump efficiency Vs. Discharge
3.To find out Torque with the help of swinging frame motor  

UTILITIES REQUIRED:
Water Supply.
Drain
Electricity 220V AC, Single Phase.
Space required: 1.6 x 0.6 m. 

TECHNICAL SPECIFICATIONS:

1.      Pump : Double acting, Single Cylinder, Capacity 3 HP

2.      Motor : 3 HP AC Motor swinging frame type with Variable Frequency Drive for variable speed.

3.      Spring Balance : Suitable capacity, Standard make

4.      Pressure gauges (2 Nos.) : Bourden tube type

5.      Vacuum gauge on the suction to measure suction head

6.      Pressure gauge on the delivery pipe to measure delivery head

7.      Sump Tank : Material Stainless Steel Capacity 180 Ltrs.

8.      Measuring Tank : Material Stainless Steel, Capacity 75 Ltrs.

Control panel comprises :

With Standard make ON/OFF Switches, Mains Indicator, etc. Digital RPM indicator : Digital RPM Indicator with proximity sensor Digital Energy Meter and variable speed AC Drive. Stop Watch : Electronic  An ENGLISH instructional manual will be provided along with apparatus.

The whole set-up is well designed and arranged in a good quality painted structure.

Make : TECHNOSYS
Model No : FM-TS102
RECTANGULAR TILTING FLUME
Technical Details : Dimensions of Flume Flume Bed Side walls Inlet section Storage tanks Tilting Mechanism Length of the Flume: 12.5 m long excluding inlet and outlet section. (15m total length) Width of the Flume: 1.2 m Depth of the Flume: 0.8 m Flume bed material should be made of 10 mm thick or above SS 304 grade sheet. Maximum deflection of the bed should be within the range of 1 mm at the maximum load (flume filled with 50% sediment (sand, gravel) and 50% water) and tilt. Flume should have transparent 19 mm thick toughened glass as side walls on either side with intermediate stiffeners supporting the glass. Side wall deflection should be maximum 1 mm. Inlet section made from 2 mm thick SS 304 grade sheet. The inlet section to be well designed so that the flow enters the flume with little turbulence. Flow straightener to be provided at the inlet section and the water enters below it. All the storage tanks should be made from 2mm thick SS 304 grade sheet with Stainless Steel stiffener support. Motorized inclination with synchronized spindle lifting gears should be provided. The inclination adjustment should be between -0.75% to 2.5 %, 3 jacking stations each consisting 2 jacks + 1 pivot. Pumps and flow measurement Tail Gate Sediment Trap Flume Platform Railing Stair Case Nuts & Bolts Pumps (2Nos.) of reputed make along with suitable electric motor of reputed make. a) Rated flow rate (for each pump): between 125 l/s to 150 l/s b) Impeller: AISI 316 Stainless Steel (precision cast) (EN 1.4401) c) Stub shaft: AISI 316 Stainless Steel (EN 1.4404) d) Rotation speed (for each pump): Below 1600 rpm e) Head of the pump should be sufficient to recirculate the water from attached tank to channel. f) Pumps should be provided with suction and delivery valves. VFD is required to control the flow of each pump. Flow measurement to be done by Electromagnetic flow meter, attached to delivery pipe, degree of accuracy ± 0.2%. in delivery Output signal- 4-20Ma, electrode materialstainless steel 316L, digital communication – RS-485, support standard Modbus protocol with digital display. Tail gate made of SS 304 with thickness 8mm at the outlet end of the flume to achieve desired level of water in experiment section. The sediment trap should be mounted at the end of the test section and before tail gate Tanks should be arranged in such a way that it forms a gallery and should be used as a platform. Side railings should be provided for safety. There should be a grade rail throughout the top of the flume. One carriage should be provided which can move throughout length of the flume from inlet to tail gate. The instrument carrier which is capable of holding ADV, point gauge should be provided and it should move transverse direction on the carriage. A stair case is provided on either side of the flume. All the nut bolts and fasteners should be of Stainless steel All material that comes in contact with water are made of corrosion-resistant materials GRP/stainless steel as specified. 

Compact 1600C Tube Furnace with 50mm Alumina Tube & Vacuum Flanges / Valves - - TS-1600X-50-UL

TS -1600X-50-UL is a compact 50mm (2") tube furnace with Kanthal 1650 ^oC Grade SiC Rods heating elements. It is widely used in material & chemical labs to sinter all types of new material samples under vacuum or other gas conditions up to 1600^oC. The temperature of the furnace is controlled by a 30 segment programmable high precision SCR (Silicon Controlled Rectifier) digital controller with the accuracy of +/-1 ^oC. High-quality alumina tube, vacuum flanges with valves, and pressure gauge are included for immediate use. The tube furnace can be placed into a glove box to process material in various atmospheres.